端子拉力標準.doc

上傳人：大***

文檔編號：48121

上傳時間：2020-02-05

格式：DOC

頁數：10

大?。?27.50KB

《端子拉力標準.doc》由會員分享，可在線閱讀，更多相關《端子拉力標準.doc（10頁珍藏版）》請在匯文網上搜索。

1、核準審核制作鐘菊蘭1. 0目的:為確保本公司于生產過程中,端子壓著能符合品質需求而制訂此規范.2. 0范圍:此規范適用于各類端子壓著檢驗.3. 權責:3.1. 制造部：依此規范進行生產.3.2. 品保部：負責依此規范進行檢驗.4. 定義:無.5. 0內容:5.1. 端子正確鉚壓標準：5.1.1. 端子的外模壓著絕緣外被鉚壓部分須在端子內模與外模間距的1/2或2/3的位置即可.5.1.2. 端子的內模壓著導體后外露部分須超過0.21mm。5.1.3. 正確鉚壓見: 如附圖一.5.2. 端子不良鉚壓標準：5.2.1. 絕緣外被壓著過長(即絕緣外被過于靠近導體壓著部分或?qū)⒔^緣外被直接壓著于導體壓著部

2、份)，此種現象將造成銅絲易斷落。如附圖二。5.2.2. 絕緣外被壓著過短(即絕緣外被未完全被壓著或沒被端子外模包覆),此種現象將造成端子拉力不足，易脫落。如附圖三。5.2.3. 尾料切斷部分，所剩下之料頭超過1mm. 如附圖四。5.2.4. 端子內模有導體外露（分叉）. 如附圖五。5.2.5. 導體壓著過長(導體過于靠近端子頭部)，此現象將造成端子不易與5.2.6. 導體壓著過短(即導體未完全被壓著或沒被端子內模包覆),此種現象將造成端子拉力不足，易脫落。如附圖七。5.2.7. 端子內模壓著突嘴過大（超過內模的1/3）。如附圖八。5.3. 端子內模導體壓著高度測量方式：如附圖九5.4. 端子外

3、模絕緣外被壓著檢驗方式:5.4.1. 導體外被壓著后需將導線做上下90度彎曲三次,檢查絕緣被覆是否有損傷或滑出，若有表面損傷或滑出，則壓著高度須重新調整。如附圖十.5.5. 端子內模導體拉力測試及檢驗方式：如附圖十一.5.5.1. 測試長度以150mm左右為標準5.5.2. 脫去外被20mm左右。5.5.3. 以拉力計拉引測試，直到導體與端子分離，記下此時拉力計上指針之刻度即為端子拉力。5.5.4. 若端子為有外皮包裹的,測量端子拉力時先去除外皮后再測量.5.5.5. 拉力測試后應檢驗端子拉出后的狀況,若導體七股芯線全部斷在端子內模內為端子壓著高度過低,則必須重新將端子內模高度調高;若導體七股

4、芯線無一股芯線留在內模中,則必須重新將端子內模高度調低.(除鉚壓雙并線端子外)5.5.6. 雙并線合鉚壓在一端子時,端子內模時不得有芯線導體外露.雙并線之拉力在拉力規格范圍內即可,不要求符合5.6. 端子鉚壓后高度及拉力必須符合要求標準.5.6.1. 詳細見附件一:端子鉚壓規格一覽表.5.6.2. 若端子為新端子（第一次生產）暫無端子高度規格時且客戶無特別要求時，可以只記錄實際高度的測量值，其拉力是否符合要求（按線號規格核對拉力要求）而作為最終判定的依據。待一批生產完成后由QE定出該端子的高度及拉力的規格值。5.7. 端子外觀檢驗標準：5.7.1. 端子的功能端不可有開口，變形，扭曲等不良且應

5、必須保證電氣功能及實配OK。5.7.2. 端子鍍層部分不可有刮傷，露黃，氧化發黑等不良。5.8. 工程圖面中有規定客戶特殊要求時,須依工程圖面為準。6. 相關記錄:6.1. 端子測量記錄表. QAD-QP-1002-02A7. 附件:7.1. 附件一：端子鉚壓規格一覽表。附件一：端子鉚壓規格一覽表端子廠商端子規格芯線規格端子高度(mm)端子寬度(mm)保持強力（MIN）JWTCKM2501TOP-2A2501TOP-00A2501TOB-2CKM2501T22 AWG0.750.855.0KG24 AWG0.700.803.5KG26 AWG0.700.752.5KG28 AWG0.650.

6、751.5KGJWTB11TOP-224 AWG0.700.753.5KG26 AWG0.600.702.5KG28 AWG0.600.651.5KGJWTA2542T3B-00A2542T3B-222 AWG0.901.05.0KG24 AWG0.750.853.5KG26 AWG0.750.852.5KG28 AWG0.700.801.5KGJWTCKMA2543TOB-00A2543T0B-2A2543T0P-2CKM2541T22 AWG0.780.885.0KG24 AWG0.700.803.5KG26 AWG0.650.752.5KG28 AWG0.600.701.5KGJWTCK

7、MA3961T2B-2CA3961T2B-2DA3961T3B-2CA3961T3B-2DCKM396118+18 AWG1.551.6514 KG22+22 AWG1.001.308.0KG18 AWG1.051.2010 KG20 AWG1.001.107.0KG22 AWG0.951.055.0KGJWTA3961T1B-2CA3961T1B-2DCKM396124 AWG0.850.953.5KG26 AWG0.750.852.5KG/CKMCKM250324 AWG0.750.853.5KG26 AWG0.700.802.5KG28 AWG0.650.751.5KGJWTCKMA25

8、41T3B-2A2541T3B-2LA2541T3B-00A2541T3B-00LCKM2542T22 AWG0.850.955.0KG24 AWG0.800.903.5KG26 AWG0.750.852.5KG28 AWG0.700.801.5KG28+28 AWG0.800.903.5KGJWTCKMA2001TOP-2A2001TOP-2LCKM2001T30 AWG0.600.701.0KG28 AWG0.650.751.5KG26 AWG0.680.782.5KG24 AWG0.700.803.5KG26+28 AWG0.730.835.0KG附件一：端子鉚壓規格一覽表端子廠商端子

9、規格芯線規格端子高度(mm)端子寬度(mm)保持強力（MIN）CKMJWTCKM2003TA2002TOP30 AWG0.650.751.0KG28 AWG0.700.801.5KG26 AWG0.750.852.5KG24 AWG0.850.953.5KGJWTCKMC5081T2B-2C5081TOB-2CKM508218+18 AWG1.301.4014 KG16 AWG1.301.4014 KG18 AWG1.201.3012 KG20 AWG1.001.207 .0KG22 AWG0.901.105.0KG24 AWG0.850.953.5KGJWTCKMC5082TOP-2CKM5

10、081 18+18 AWG1.502.0014 KG18 AWG1.201.4012 KG20 AWG1.101.307.0KG22 AWG1.001.105.0KG24 AWG0.901.103.5KGJWTCKMC5082T2B-2CKM508116 AWG1.301.5014 KG18 AWG1.201.4012 KGJWTCKMA2544TOP-2A2544TOB-2CKM2544T20 AWG0.951.157.0KG22 AWG0.850.955.0KG24 AWG0.800.903.5KG26 AWG0.750.852.5KGCKM 2506-TA24 AWG0.800.903.

11、5KGCKM 2506-TB22 AWG0.850.955.0KGJWTCKMA1251TOP-2CKM1251T28 AWG0.500.601.5KGCKMCKM2002-TV28 AWG0.700.801.5KGCKM2004T28 AWG0.650.751.5KGCKM2542T28+28 AWG0.800.903.5KGJWTA2505TOP-2C4202T2B-2C4202T2P-222 AWG0.800.905.0KG16 AWG1.201.5014 KG18 AWG1.001.2012 KGJWTCKMA2547TOP-2CKM2543T24+24 AWG0.901.206.0K

12、G26+26 AWG0.850.955.0KG22 AWG0.901.005.0KG24 AWG0.850.953.5KG26 AWG0.800.902.5KG28 AWG0.700.801.5KG附件一：端子鉚壓規格一覽表端子廠商端子規格芯線規格端子高度(mm)端子寬度(mm)保持強力（MIN）JWTA2003TOB-00A2003TOB-2A2003TOB-0D26 AWG0.550.652.5KG28 AWG0.500.621.5KG30 AWG0.500.601.0KGJWTCKMA2005TOB-2A2005TOB-00CKM2004T26 AWG0.700.802.5KG28 A

13、WG0.650.751.5KG30 AWG0.600.701.0KGJWTCKMA3963TOB-23963TOP-2CKKM396218+18 AWG1.502.0014 KG18 AWG1.001.3012 KG20 AWG0.901.007.0KG22 AWG0.850.955.0KG24 AWG0.800.903.5KGJWTCKMA3963T2B-2A3963T2P-214 AWG1.301.7015 KG16 AWG1.201.5014 KG18 AWG1.001.3012 KGJWTCKMC4202TOP-2C4202TOB-2CKM420116 AWG1.201.4014 KG

14、18 AWG1.001.2012 KG20 AWG0.901.107.0KG22 AWG0.801.005.0KGJFE260901T24 AWG0.89+/-0.051.45+/-0.053.5KG260902T28 AWG0.63+/-0.051.45+/-0.051.8KGJSTSHE-001T-P0.624 AWG0.750.803.5KG26 AWG0.680.752.5KG28 AWG0.650.701.5KGJSTSPH-002T-P0.5S30 AWG0.600.651.0KG28 AWG0.650.721.5KG26 AWG0.650.752.5KG24 AWG0.700.8

15、03.5KGJWTC5082TOB-218 AWG1.251.3512KGC5082TOB-222+18 AWG1.451.5512KGC5082T2B-218+18 AWG1.501.6014KGC5082TOB-218+18 AWG1.451.5514KGJWTA1561TOP-222 AWG1.001.105.0KGJWTB1811TOP-218 AWG1.101.2010KGCKM2543T28+28 AWG0.80.903.5KGCKM2503T28+26 AWG0.800.903.5KGCKM5081T20+20 AWG1.351.4512KG附件一：端子鉚壓規格一覽表端子廠商端

16、子規格芯線規格端子高度(mm)端子寬度(mm)保持強力（MIN）CKM1561T22 AWG1.001.105.0KGJWTA1561TOB+222 AWG0.800.905.0KGJWTB1811TOP-228 AWG0.951.051.5KGJWTA3961T2B-2C18 AWG1.051.2010KGCKM2542T28+28AWG0.800.903.5KGCKM2004T28 AWG0.650.751.5KGJWTCKMA2001TOP-2A2001TOP-2LCKM2001T28 AWG0.600.701.5KG30 AWG0.650.751.0KG26+28 AWG0.730.8

17、35.0KG24 AWG0.700.803.5KG26 AWG0.650.752.5KGJWTA1251TOP-228 AWG0.500.601.5KGCKMCKM3962T18 AWG1.001.3012KGCKMCKM2002-TV28 AWG0.700.801.5KGJWTC4202TOP-2C4202TOB-2CKM420116 AWG1.201.5014KG18 AWG1.101.2012KG20 AWG1.001.107.0KG22 AWG0.901.005.0KGJWTC4202T2B-216 AWG1.201.5014KGJWTC4202T2P-218 AWG1.001.201

18、2KGCKM3963-T22 AWG0.850.955.0KGCKM2503T22 AWG0.800.905.0KGALEX2580T28AWG0.600.701.5KG22 AWG0.750.855.0KG2015T28 AWG0.550.651.5KG22 AWG0.700.805.0KG4256TP316 AWG1.301.5014.0KG51T22 AWG0.750.855.0KGMOLEX08-50-011422 AWG0.750.855.0KG08-50-011426 AWG0.700.802.5KG08-50-010522 AWG0.951.055.0KG16-02-010722

19、 AWG0.800.905.0KG胡鏈604180-2編織線1.651.802.53.210KG翔輝SH-99518 AWG一分鐘吊重9.1KG不脫落為合格.鉚壓F/BNC-CONN:出力達7.0KG為合格Molex39-00-006522 AWG0.850.955.0KGMolex39-00-006722 AWG0.850.955.0KG附件一：端子鉚壓規格一覽表端子廠商端子規格芯線規格端子高度(mm)端子寬度(mm)保持強力（MIN）AMP104505-0322 AWG0.901.005.0KG35085-118 AWG1.251.3512 KG770601-218 AWG0.700.8

20、012 KG104505-B22 AWG0.850.955.0KG104503-322 AWG0.850.955.0KG170362-122 AWG0.951.055.0KG104480-422 AWG0.850.955.0KG2-36152-118 AWG2.703.0012 KG1757778-328 AWG0.750.851.5KG170204-122 AWG0.850.955.0KG170360-118 AWG1.051.1512 KG17026222 AWG0.951.055.0KG350570-118 AWG1.21.512 KG104504-322 AWG0.850.955.0K

21、G2-520403-222 AWG0.850.955.0KG66105-324 AWG0.750.853.5KG66424-728 AWG0.750.851.8KG61116-420+20 AWG1.551.6512KG50011-800028 AWG0.520.621.5KG640271-118 AWG2.002.1010KG63475-222AWG1.101.305.0KG22+22 AWG1.401.508.0KG61070-122 AWG1.101.205.0KG71180-BS-118 AWG1.351.4510KG55675-122AWG2.503.005.0KG602207-21

22、8 AWG1.502.0010 KGJAEIL-G-C2-SA-1000024 AWG0.750.851.51.63.5KG28 AWG0.650.7251.51.61.5KGDUPONT75653-00522 AWG0.901.005.0KG47445-0022 AWG0.901.005.0KG47217-00022 AWG0.901.005.0KG24 AWG0.850.953.5KGT-UBAC11-BN-5S-D-V0128 AWG0.730.831.5KGT-UBAC10-BN-5S-D-V0124 AWG0.931.133.5KGT-UBAC14-BN-5S-D-V0120 AWG

23、1.001.257.0KGTDP8810T22 AWG0.800.905.0KG附件一：端子鉚壓規格一覽表端子廠商端子規格芯線規格端子高度(mm)端子寬度(mm)保持強力（MIN）KSTFDFV-187(5)18 AWG1.101.2010KGKSTRNBS1-3.718 AWG2.352.4512KGKSTRNB-1-522 AWG2.002.505.0KGV.35(公、母)30 AWG0.750.851.0KG28 AWG0.800.901.5KG26 AWG0.880.982.5KG24 AWG0.951.303.5KG22 AWG 0.981.505.0KG20 AWG1.001.6

24、07.0KGT-UAC10-1020024 AWG0.931.133.5KGT-UAC10-2020028 AWG0.730.831.5KG0.76圓形端子24 AWG0.750.953.5KG28 AWG0.650.751.5KG1.0圓形端子24 AWG0.750.853.5KG26 AWG0.720.822.5KG28 AWG0.700.801.5KGRVS2-3.718 AWG2.503.5010KGTA1BA000E24 AWG0.830.953.5KGTA1BA000E28 AWG0.730.831.5KGTAB1000E24 AWG0.830.953.5KG26 AWG0.780

25、.902.5KG28 AWG0.730.831.5KGWST139601BS-218 AWG0.901.0310KGFDFD2-25014 AWG3.504.5015KGFDFD2-25016 AWG3.004.0014KGFDFD2-25018 AWG3.004.0010KGJSTSVH-21T-P1.118 AWG1.001.3010KGSTM2131BS接地線1.150.052.050.0510KGPACKARD:接地線1.150.052.050.0510KGFDD1-25018 AWG3.004.0010KGCUSTIMER CONSIGN22 AWG0.850.955.0KGMPNY

26、1-156(公)18 AWG1.601.7012KGFRD1-156(母)18 AWG1.851.9512KG世聚T202P00T0024 AWG0.700.803.5KG旗欣255128+28 AWG0.750.852.5KG附件一：端子鉚壓規格一覽表端子廠商端子規格芯線規格端子高度(mm)端子寬度(mm)保持強力（MIN）MOLEX08-50-011328 AWG0.650.751.5KG26 AWG0.700.802.5KG24 AWG0.750.853.5KG22 AWG0.800.905.0KG08-50-010618 AWG1.001.3012 KG20 AWG0.850.957

27、.0KG22 AWG0.800.905.0KG43030-000322 AWG0.850.955.0KG02-09-210318 AWG1.301.8012 KGAS-N-34518 AWG2.002.5012 KG08-65-080426+28 AWG0.800.905.0KG02-08-123420+20 AWG1.601.8012KG02-08-123420 AWG1.451.657.0KG02-08-120120+20 AWG1.751.9512KG02-08-120120 AWG1.351.557.0KG43030-000120 AWG1.101.207.0KG22-01-10422

28、8+26 AWG0.850.953.5KG43030-000722 AWG0.901.005.0KG43030-000120 AWG1.001.107.0KG39-00-006118+18AWG1.401.5014KG02-06-210120 AWG0.901.107.0KG02-06-110120 AWG0.850.957.0KG 16-02-008228 AWG0.700.801.5KG24 AWG0.850.953.5KG16-02-111926 AWG0.800.852.5KG28 AWG0.750.801.5KG16-02-011926 AWG0.700.802.5KG39-00-0

29、03818 AWG1.101.2012KG39-00-005318 AWG1.101.2012KG08-70-010618 AWG0.951.0512KG20 AWG0.901.007.0KG22 AWG0.850.955.0KG08-70-103118 AWG1.201.5012KG20 AWG1.001.307.0KG22 AWG0.901.105.0KG24 AWG0.850.953.5KG附件一：端子鉚壓規格一覽表端子廠商端子規格芯線規格端子高度(mm)端子寬度(mm)保持強力（MIN）其它端子類型:芯線規格拉力(MIN)芯線規格拉力(MIN)芯線規格拉力(MIN)橫卷線4.5KG2

30、2 AWG5.0KG32 AWG0.8KG編織線10 KG26 AWG2.5KG10 AWG36.4KG14 AWG15 KG28 AWG1.5KG12 AWG31.9KG16 AWG14 KG30 AWG1.0KG20 AWG7.0KG18 AWG12 KG24+24AWG6.0KG26+26 AWG5.0KG端子廠商端子規格芯線規格端子高度(mm)端子寬度(mm)保持強力（MIN）ALEX26T-6502-PB22 AWG0.921.025.0KGALEX61T-552418+22 AWG1.551.6512KGMOLEX39-00-006118 AWG1.061.6610KGMOLEX39-01-208024+24AWG0.901.26.0KGMOLEX39-00-003824AWG0.850.953.5KGJSTSYM-001P-P0.624AWG1.01.13.5KGAMP170147-122AWG1.151.255.0KGAMP350689-122AWG0.91.05.0KG10

下載提示：本站僅提供存儲空間/不修改/不編輯

1.請仔細閱讀文檔，確保文檔完整性，對于不預覽、不比對內容而直接下載帶來的問題本站不予受理。
2.下載的文檔，不會出現我們的網址水印。
3、該文檔所得收入（下載+內容+預覽）歸上傳者、原創作者；如果您是本文檔原作者，請點此認領！既往收益都?xì)w您。

同意并開始全文預覽

文檔包含非法信息？點此舉報后獲取現金獎勵！

文檔加載中……請稍候！
如果長時間未打開，您也可以點擊刷新試試。

下載文檔到電腦，查找使用更方便

10 積分

下載	加入VIP,下載共享資源

還剩頁未讀，繼續閱讀

舉報

版權申訴 word格式文檔無特別注明外均可編輯修改；預覽文檔經過壓縮，下載后原文更清晰！ 立即下載

配套講稿：: 如PPT文件的首頁顯示word圖標，表示該PPT已包含配套word講稿。雙擊word圖標可打開word文檔。
特殊限制：: 部分文檔作品中含有的國旗、國徽等圖片，僅作為作品整體效果示例展示，禁止商用。設計者僅對作品中獨創性部分享有著作權。
關 鍵詞：: 端子拉力標準

匯文網所有資源均是用戶自行上傳分享，僅供網友學習交流，未經上傳用戶書面授權，請勿作他用。