《常用注塑術語中英文對照表.doc》由會員分享，可在線閱讀，更多相關《常用注塑術語中英文對照表.doc（3頁珍藏版）》請在匯文網上搜索。

1、常用注塑術語中英文對照表注塑參數Injection parameter注射量Injection rate計量行程Screw back position余料量Cushion防誕量Sucking back rate螺桿轉速Screw speed塑化量Plastic rate預塑背壓Screw back pressure注射壓力Injection pressure保壓壓力holding pressure/packing pressure注射速度Injection speed/velocity合模參數Clamping parameter合模力Clamping force合模速度Clamping spe

2、ed/velocity合模行程Clamping stroke開模力Opening force開模速度Opening speed/velocity開模行程Opening position頂出壓力Ejector advance pressure頂出速度Ejector advance speed/velocity頂出行程Ejector advance position溫控參數Temperature parameter烘料溫度Dry resin material temperature料筒Cylinder temperature噴嘴溫度nozzle temperature模具溫度Mold temper

3、ature油溫Oil temperature成型周期Molding cycle循環周期Cycle time冷卻時間Cool time注射時間Injection time保壓時間Holding pressure time塑化時間Plant time頂出Knocking out time停留時間delay time低壓保護時間Mold protect time注塑英語大全 成型工藝流程及條件介紹Molding technique procedure and parameter introduction 第一節 成型工藝Section 1 molding technique. 1.成型工藝參數類型S

4、orts of molding parameter. (1).注塑參數ction parameter. a.注射量ction rate. b.計量行程Screw back position c.余料量Cushion d.防誕量Sucking back rate e.螺桿轉速Screw speed f.塑化量Plastic0 rate g.預塑背壓Screw back pressure h.注射壓力和保壓壓力ction pressure and holding pressure i.注射速度ction speed (2)合模參數Clamping parameter a.合模力 Clamping

5、force b.合模速度Clamping speed c.合模行程.Clamping stroke d.開模力Opening force e.開模速度Opening speed f.開模行程Opening position g.頂出壓力Ejector advance pressure h.頂出速度Ejector advance speed i.頂出行程Ejector advance position 2.溫控參數Temperature parameter a.烘料溫度Dry resin material temperature b.料向與噴嘴溫度Cylinder temperature and

6、 nozzle temperature c.模具溫度Mold temperature d.油溫Oil temperature 3.成型周期Molding cycle a.循環周期Cycle time b.冷卻時間Cool time c.注射時間ction time d.保壓時間Holding pressure time e.塑化時間Plant timf.頂出及停留時間Knocking out and delay time g.低壓保護時間Mold protect time成型工藝參數的設定須根據產品的不同設置. Molding technique parameter setting diffe

7、rs depending on type of product 第二節成型條件設定 Section 2 Molding parameter Setting 按成型步驟:可分為開鎖模,加熱,射出,頂出四個過程.Molding steps: mold opening/closing, heating ction and knocking out. 開鎖模條件: Mold opening parameter: 快速段中速度 High-speedmid-speed 低壓高壓速度 Low pressure high pressure speed 鎖模條件設定: Mold closing parameter setting 1鎖模一般分:快速中速低壓高壓Mold closing: high-speed low-speed low pressurehigh pressure