《微軟認證模擬試題：TCP-IP考題.docx》由會員分享，可在線閱讀，更多相關《微軟認證模擬試題：TCP-IP考題.docx（8頁珍藏版）》請在匯文網上搜索。

1、微軟認證模擬試題：TCP/IP考題Question 1. Under Windows NT, what command would you use if you wanted to trace a packet from its source host to a destination host?A. TRACERTB. ROUTEC. NBTSTATD. IPCONFIGThe TRACERT utility is Microsoft's own, used to trace a packet from its source ( your computer ) to a destin

2、ation host (a remote computer ).Question 2. If you wanted to display all entries in the ARP cache, which of the following utilities would you use?A.ARP -GB. ARP - EC. ARP - DD. ARP - STo display all entries in the ARP ( Address Resolution Protocol ) cache, you would use the ARP utility with the -G o

3、r -A switch. They are the same thing. To get the answer type "arp /?" at the command prompt.ARP ( Address Resolution Protocol ) is used to obtain hardware ( MAC = Media Access Control ) addresses for communications with a destination host.Question 3. You notice that the subnet mask is 0.0.

4、0.0 on your Windows NT computer while using the IPCONFIG utility at the command prompt to check for IP address configuration. What does it mean when the IPCONFIG utility displays a subnet mask of 0.0.0.0?A. The default gateway on your computer does not match the default gateway of the network.B. You

5、r computer has the same subnet mask as another computer on the network.C. Your computer does not have the correct IP address class specified for it.D. Your computer has the same IP address as another computer on the network.The most likely cause in this scenario is that your computer has the same IP

6、 address as another computer in the network. When this happens, running IPCONFIG will yield anIP address of 0.0.0.0.Question 4. If you want to copy files from one WindowsNT computer to another, what TCP / IP utility would you use?A . RCPB. REXECC. TELNETD. TRACERTThe RCP ( Remote Copy ) is Microsoft

7、's own TCP / IP utility. It is used to copy files from a source Windows NT computer to a destination ( remote ) Windows NT computer, or vice-versa. Type "rcp /?" at the command prompt to get the command's full syntax.Question 5. Use the following diagram to answer this question :Yo

8、u are working on your Windows NT workstation, SMALLNT, and you would like to communicate with another Windows NT computer, BIGNT. If both computers are on the same local subnet , where does SMALLNT look for the hardware address of the destination host? ( BIGNT in this case )A. In its own ARP cache.B

9、. In the ARP cache of the destination host, BIGNT in thiscase.C. If there is a DHCP server present , then in the ARP cache of the DHCP server.D. In the LMHOSTS or HOSTS file of the source computer.The ARP protocol ( and NOT the ARP command ) is used to map IP addresses to hardware addresses ( MAC ad

10、dresses ). Anytime you communicate with a destination host that is on the same subnet ( locally ), then the hardware address of the destination host is obtained from the source host's LOCAL ARP cache. In this scenario, BIGNT's hardware address is obtained from SMALLNT's own ARP cache sin

11、ce both computers are on the same network.Question 6. You have a print device connected to a server running the LPD service. From your Windows NT computer, you would like to obtain the status of the print device. What utility would you use to achieve the task?A. LPDB. NET USEC. LPQD. GETDAEMONThe LP

12、D ( Line Printer Daemon ) is a TCP / IP printing service. A print server that has a TCP / IP print device connected to it must have the LPD service installed on it. However, to obtain the status of a TCP / IP print device ( or print queue as it is often called in the TCP / IP circle ), you would use

13、 the LPQ command.Type "lpq /?" at the command prompt to get the proper syntax. Pay close attention to the "-S" and "-P" switches. For the "-S" switch, you can specify the NAME or IP address of the print server running the LPD service.Question : Under Windows N

14、T Server 4.0, how do you install the LPD service?Answer : Under Windows NT, the LPD service is known as "Microsoft TCP / IP Printing" = right-click Network Neighborhood | Properties | Services tab | Add. | "Microsoft TCP / IP Printing" service.Question 7. Let's say that you w

15、ant to run a process on a remote host that is using the REXEC service, what Microsoft TCP / IP utility would you use?A. RCPB. REXECC. TELNETD. FTPThe REXEC ( Remote Execute ) command is Microsoft's home-grown utility used to run processes on a remote computer that is also running the REXEC servi

16、ce. Type "rexec /?" at the command prompt to get the full syntax.Question 8. If you want to retrieve system information from a remote host running the Finger service, what TCP / IP utility would you use?A. REXECB. PINGC. RCPD. FINGERThe FINGER utility is used to obtain system information from a remote host that is using the Finger service. To get the proper syntax, type